How To Set Up Paint Gun

Accept you lot always wondered what it would take to pigment your ain motorcar? Save yourself tons of money by doing the paint job at habitation. For years the standard spray gun was a Binks siphon fed gun. These spray guns were all-time used with lacquer based paint while holding huge distances from the panels to utilise the paint. As paint technology increased so did the need for new paint guns to lay smooth glass like finishes. Born were beginning HVLP (High Volume Low Pressure). These paint guns increased the efficiency of how much pigment actually made it to the panel saving you from wasted paint. At present instead of holding the paint gun up to 18 inches from the panel these new guns accept you spraying at 6-8 inches.

Now allow'southward get into the reason you all clicked to read this article, how to properly gear up the spray gun to achieve the best possible pigment job.  The spray gun I will be using equally an example will exist our Concours Pro paint gun. The first thing I will talk about setting upwardly will exist air pressure since this can and should be done before you even put paint into your gun. Each spray gun will take three controls and their locations may differ slightly.  Check your instructions to ensure you move the correct controls. Since that is out of the style permit's show you where on the Eastwood Concours Pro y'all tin can find the air command.

. Air Regulator on Pigment Gun

This effigy on the left shows where the air control is located. I always recommend leaving this command broad open for 99% of your painting. This way you can get a much more authentic pressure by attaching a force per unit area regulator as you see pictured to the correct of the spray gun. A peachy lightweight option is the Concours Pro Air Regulator. With this attached right at the base of your gun you lot can pull the trigger as if yous were painting all the way back and start making adjustments to the regulator. We recommend painting between 25-thirty psi while the trigger is pulled. You may run into some pigment tech sheets which refer to a painting air pressure level of eight-10. Don't set the spray gun to those as this measurement is referring to the air cap pressure level correct where the pigment comes out. This is a measurement that merely the pigment gun manufacture has the approximate to read. But by setting your spray gun to the recommended 25-30 PSI at the base y'all will achieve proper air cap force per unit area.

This next prototype is of the location of the fluid control. This changes how far the fluid needle can exist pulled back ultimately controlling how much paint can come out when you pull the trigger. If you lot tighten this all the way in you'll actually exist able to brand it so you cannot even pull the trigger far enough to let any paint out. The recommended setting for this is a tricky 1 as it is more about personally preference. Most painters, including myself, recommend leaving the fluid control all the way open to allow the maximum corporeality through to create a squeamish moisture coat each fourth dimension you spray. Then, if you need simply a mist of paint to somewhere such equally a tight corner, y'all can but slightly pull back on the trigger to let a niggling bit of paint back.

The concluding control which is very of import will be the fan command. The "fan" is how long the shape of spray pattern is.  If y'all spray a test on a scrap piece of paper or cardboard for a divide 2nd you lot will want to run across the pigment resemble a football shape. The fan control allows you to alter the shape from a football game all the way downward to a dot.  For over all paint jobs such as an exterior of a vehicle we recommend taking your fan control and opening it all the way upwards then turn it back down an 1/8 to a one/four turn. This will achieve the best atomization of your paint to requite you the best possible results. Hopefully this will let you to comfortably understand the settings of your new spray gun. If you're all the same hungry for some more information we accept an excellent video with Kevin Tetz which goes fifty-fifty farther in depth to make sure your next paint job turns out correct and makes people say WOW.  Click here to jump on over to our YouTube aqueduct to see Kevin in action. If yous'd like to see our consummate line of paint guns, which not but include Eastwood but all of the other popular brands like Iwata and Devilbiss, you tin see them on the HVLP Paint Gun Page.

Source: https://garage.eastwood.com/painting-powdercoating/how-to-set-up-an-hvlp-spray-gun/

Share this post